Visonic PowerMax10 Specifiche Pagina 40
- Pagina / 78
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
D-302756 39
7.
Press
OKI
and make the selection and then press
OKI
to confirm.
The PowerMax10-G2 display will revert to [13:SWINGER STOP].
OKI
SELECT OPTION
OKI
You can now press the or button to program any other menu in
"
DEFINE PANEL
" or press the button to take you to "
<OK> TO EXIT
".
4.7.3 Enable Monitoring of Activity at Home
Here you determine the time limit for reception of signals from sensors used to monitor the activity of sick, elderly or
disabled people. If no sensor detects and reports movement at least once within the defined time limit, a “not-active” alert is
initiated.
Options: 3, 6, 12, 24, 48, 72 hours and no act disable (default).
To Configure Monitoring of Activity at Home
1. Make sure the system is disarmed and then press the button
repeatedly until the PowerMax10-G2 display reads "INSTALLER MODE".
2.
When the PowerMax10-G2 display reads [INSTALLER MODE], press
OKI
.
The screen will now prompt you to enter your installer code.
OKI
3.
Enter your Installer Code.
CODE
4. Press the or button repeatedly and select the [DEFINE PANEL]
option.
or
5. When the PowerMax10-G2 display reads [DEFINE PANEL], press
OKI
The PowerMax10-G2 display will read [01:ENTRY DELAY 1].
OKI
6.
When the PowerMax10-G2 display reads [01:ENTRY DELAY 1], press
the
or button repeatedly until the display will read [21:NOT ACTIVE].
or
7.
Press
OKI
and make the selection and then press
OKI
to confirm.
The PowerMax10-G2 display will revert to [21:NOT ACTIVE].
OKI
SELECT OPTION
OKI
You can now press the or button to program any other menu in
"
DEFINE PANEL
" or press the button to take you to "
<OK> TO EXIT
".
4.7.4 Configuring Alarm Cancel Period
Here you determine the ”cancel alarm” period that starts upon reporting an alarm to the Monitoring Station. If the user
disarms the system within that time period, a “cancel alarm” message is sent to the Monitoring Station.
Available options are: cancel time 1 m, cancel time 5 m (default), cancel time 15 m, cancel time 60 m, cancel time
4 hours and also cancel inactive (default in USA).
Note: To comply with CP-01 requirements, "1 minute" option is not available.
To Configure the Alarm Cancel Period
1. Make sure the system is disarmed and then press the button repeatedly
until the PowerMax10-G2 display reads "INSTALLER MODE".
2.
When the PowerMax10-G2 display reads [INSTALLER MODE], press
OKI
.
The screen will now prompt you to enter your installer code.
OKI
3.
Enter your Installer Code.
2
1:NOT ACTIVE
13:SWINGER STOP
E
NTER CODE:
INSTALLER MODE
R
EADY 00:00
2
1:NOT ACTIVE
0
1:ENTRY DELAY 1
E
NTER CODE:
INSTALLER MODE
R
EADY 00:00
D
EFI
N
E PANEL
- PowerMax10 1
- PowerMax10-G2 2
- 2.5 Physical Properties 5
- 3. INSTALLATION 5
- 3.2 System Planning & 7
- Programming 7
- 3.3 Mounting the Unit 7
- 3.4.1 GSM Installation 8
- 3.4.2 PowerLink Installation 8
- 4. PROGRAMMING 9
- 4.1 General Guidance 9
- 4.2 Navigation 9
- NEW INST. CODE 10
- <OK> TO EXIT 10
- NEW MASTER CODE 11
- 36:USER PERMIT 11
- DEFINE PANEL 11
- 25:RESET OPTION 12
- 4.4 Zones / Devices 13
- SAME Dev 15
- EXIT Enrollment 15
- ADD NEW DEVICES 15
- NEXT device 15
- 4.4.2.4 Locations 16
- 4.4.3 Adding Wired Zones 17
- Z01:Motion Sens] 18
- <OFF> to delete] 18
- <OFF> to delete 18
- Z01:Motion Sens 18
- 4.5 Siren Configuration 20
- AREA CODE 23
- GPRS REPORT 26
- 1st RPRT METHOD 27
- RCVR 1 ACCOUNT# 28
- PSTN/GSM RCVR1 29
- PSTN RPRT RETRY 31
- AUTO TEST TIME 32
- PSTN UP/DOWN 34
- REPORT EVENTS 35
- 36
- 4th private tel#] 37
- SMS REPORT TEL# 38
- <OK> 38
- 1st private tel# 38
- 4.10 DEFINE CUSTOM LOCATIONS 54
- 5 DIAGNOSTIC TEST 62
- 5.1 Testing Devices 63
- NO DEVICES 66
- LAN RESET OPTION 66
- WL DEVICES 68
- 7. MAINTENANCE 69
- 7.1 Handling System Troubles 69
- 7.4 Fuse Replacement 70
- 7.6 Restore Factory Defaults 70
- 7.7 Viewing Serial Number 71
- 8 READING THE EVENT LOG 71
- 8.1 Reading the Event Log 71
- A1. Detector Deployment Plan 72
- A2. Keyfob Transmitter List 73
- APPENDIX B. Event Codes 74
- B1. Contact ID Event Codes 74
- B2. SIA Event Codes 74
- B3. 4/2 Event Codes 74
- APPENDIX C. Glossary 75
- Industry Canada Declaration 77
Prodotti e manuali riguardandi Sistemi di controllo di accesso Visonic PowerMax10
(76 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale